Goeckner, Matthew J.

Permanent URI for this collectionhttps://hdl.handle.net/10735.1/2487

Matthew Goeckner is Professor of Mechanical and Electrical Engineering as well as Program Head of Mechanical Engineering. His research interests include plasma-materials interactions, plasma science, and material growth kinetics. Learn more about Dr. Goeckner on his home and Research Explorer pages.


Recent Submissions

Now showing 1 - 7 of 7
  • Item
    Correction of Aspect Ratio Dependent Etch Disparities
    (A V S Amer Inst Physics) Bates, Robert L.; Goeckner, Matthew J.; Overzet, Lawrence J.; 0000 0000 5396 3610 (Goeckner, MJ); 0000 0003 5379 4329 (Overzet, LJ); 2008008261‏ (Goeckner, MJ)
    The etch rate of deep features in silicon, such as trenches and vias, can vary significantly with the feature aspect ratio (AR). Small AR features generally etch faster than large AR features. The reasons for this AR dependence include a slowing of the etch rate with increasing AR due to the necessary transport of molecules into and out of the features as well as ion flux reductions at feature bottom due to the angular spread of the ion flux and ion deflection caused by differential charging of the microstructures. Finding ways to reduce, eliminate, or reverse this AR dependence is both an active subject of research and difficult. In this work, instead of focusing on methods to reduce or prevent AR dependence in an etch process, the authors focus on methods to correct it after the fact. The authors show that an inhibitor film deposition step can be used under some circumstances to allow feature depth disparities to be corrected. This process can be used to correct feature depth disparities whenever the AR dependence of the inhibitor film deposition step is worse (larger) than the AR dependence of the following inhibitor etch step. To test the theory, a plasma process through SF₆/C₄F₈/Ar mixtures was used to both produce trenches of various ARs having significant depth disparities and correct those disparities. The etch depth of small AR features can be held essentially constant while that of larger AR features is increased to match or even exceed.
  • Item
    Silicon Etch Using SF₆/C₄F₈/Ar Gas Mixtures
    Bates, Robert L.; Thamban, P. L. Stephan; Goeckner, Matthew J.; Overzet, Lawrence J.; 0000 0000 5396 3610 (Goeckner, MJ); 0000 0003 5379 4329 (Overzet, LJ); 0000 0001 2766 4681 (Thamban, PLS); 2008008261‏ (Goeckner, MJ)
    While plasmas using mixtures of SF₆, C₄F₈, and Ar are widely used in deep silicon etching, very few studies have linked the discharge parameters to etching results. The authors form such linkages in this report. The authors measured the optical emission intensities of lines from Ar, F, S, SFx, CF₂, C₂, C₃, and CS as a function of the percentage C₄F₈ in the gas flow, the total gas flow rate, and the bias power. In addition, the ion current density and electron temperature were measured using a floating Langmuir probe. For comparison, trenches were etched of various widths and the trench profiles (etch depth, undercut) were measured. The addition of C₄F₈ to an SF₆/Ar plasma acts to reduce the availability of F as well as increase the deposition of passivation film. Sulfur combines with carbon in the plasma efficiently to create a large optical emission of CS and suppress optical emissions from C₂ and C₃. At low fractional flows of C₄F₈, the etch process appears to be controlled by the ion flux more so than by the F density. At large C₄F₈ fractional flows, the etch process appears to be controlled more by the F density than by the ion flux or deposition rate of passivation film. CF₂ and C₂ do not appear to cause deposition from the plasma, but CS and other carbon containing molecules as well as ions do.
  • Item
    Electron Beam Excitation Method to Study Gas Phase During Etch Processes
    Stephan Thamban, P. L., 1975-; Padron-Wells, Gabriel; Yun, Stuart; Hosch, Jimmy W.; Goeckner, Matthew J.; 0000 0000 5396 3610 (Goeckner, MJ); 0000 0001 2766 4681 (Thamban, PLS); 2008008261‏ (Goeckner, MJ)
    In process optical emission spectroscopy (OES) measurements, excitation mechanisms as dictated by the process plasma can be complex to analyze optical signals quantitatively. Applications of a new electron beam excitation method demonstrate distinct merits for plasma process diagnostics and process control. The electron energy control attribute of the method provides the means to optimize and monitor specific species optical emission in process chemistries to achieve process control such as endpoint. The authors present gas phase results from photoresist ash and SiO2 etch using O-2 and CF4/Ar discharges, respectively. The effluent density variations as measured with the e-beam method during process stages demonstrate process endpoint detection. Simultaneous measurements with FTIR spectroscopy and direct plasma OES is also presented for comparison.
  • Item
    Temperature Dependence of the Infrared Absorption Cross-Sections of Neutral Species Commonly Found in Fluorocarbon Plasmas
    Nelson, Caleb T.; Overzet, Lawrence J.; Goeckner, Matthew J.; 0000 0000 5396 3610 (Goeckner, MJ); 0000 0003 5379 4329 (Overzet, LJ); 2008008261‏ (Goeckner, MJ)
    This article serves as a reference for the analysis of Fourier transform infrared spectroscopy data from processing plasmas. Until now, there has been a lack of accurate reference data for addressing the problems of species identification and density measurements in cases of increasing gas temperatures. Our results show that, while the integrated absorption cross-sections do not change significantly as temperature increases, the temperature of the absorbing species can be estimated from the rotational band maximum in most cases. Integrated absorption cross-sections for c-C3F6, C4F8, C3F8, C2F6, C2F4, and CF4 are presented for all fundamental bands in the 650 cm(-1) to 2000 cm(-1) region. In addition, the binary combination bands up to 4000 cm(-1) are presented for all species. The temperature of each species has been varied to correspond to neutral temperatures commonly found in processing plasmas.
  • Item
    Role of Surface Temperature in Fluorocarbon Plasma-Surface Interactions
    Nelson, Caleb T.; Overzet, Lawrence J.; Goeckner, Matthew J.; 0000 0000 5396 3610 (Goeckner, MJ); 0000 0003 5379 4329 (Overzet, LJ); 2008008261‏ (Goeckner, MJ)
    This article examines plasma-surface reaction channels and the effect of surface temperature on the magnitude of those channels. Neutral species CF4, C2F6, and C3F8 are produced on surfaces. The magnitude of the production channel increases with surface temperature for all species, but favors higher mass species as the temperature is elevated. Additionally, the production rate of CF2 increases by a factor of 5 as the surface temperature is raised from 25 degrees C to 200 degrees C. Fluorine density, on the other hand, does not change as a function of either surface temperature or position outside of the plasma glow. This indicates that fluorine addition in the gas-phase is not a dominant reaction. Heating reactors can result in higher densities of depositing radical species, resulting in increased deposition rates on cooled substrates. Finally, the sticking probability of the depositing free radical species does not change as a function of surface temperature. Instead, the surface temperature acts together with an etchant species (possibly fluorine) to elevate desorption rates on that surface at temperatures lower than those required for unassisted thermal desorption.
  • Item
    Gain and Loss Mechanisms for Neutral Species in Low Pressure Fluorocarbon Plasmas by Infrared Spectroscopy
    Nelson, Caleb T.; Overzet, Lawrence J.; Goeckner, Matthew J.; 0000 0000 5396 3610 (Goeckner, MJ); 0000 0003 5379 4329 (Overzet, LJ); 2008008261‏ (Goeckner, MJ)
    This article examines the chemical reaction pathways of stable neutral species in fluorocarbon plasmas. Octafluorocyclobutane (c-C4F8) inductively coupled plasma discharges were found to primarily produce stable and metastable products downstream from the discharge, including c-C4F8, C2F4, C2F6, CF4, C3F8, C4F10, C3F6, and CF2. A novel analysis technique allows the estimation of gain and loss rates for neutral species in the steady state as functions of residence time, pressure, and discharge power. The gain and loss rates show that CF4, C2F6, C3F8, and C4F10 share related gain mechanisms, speculated to occur at the surface. Further analysis confirms that CF2 is predominantly produced at the chamber walls through electron impact dissociation of C2F4 and lost through gas-phase addition reactions to form C2F4. Additionally, time-resolved FTIR spectra provide a second-order rate coefficient of 1.8 x 10(-14) cm(3)/s for the gas-phase addition of CF2 to form C2F4. Finally, C2F4, which is much more abundant than CF2 in the discharge, is shown to be dominantly produced through electron impact dissociation of c-C4F8 and lost through either surface or gas-phase addition reactions.
  • Item
    Comparison endpoint study of process plasma and secondary electron beam exciter optical emission spectroscopy
    (American Vacuum Society, 2012-10-03) Thamban, P. L. Steven; Padron-Wells, Gabriel; Hosch, Jimmy W.; Yun, Stuart; Goeckner, Matthew J.; 0000 0001 2766 4681 (Thamban, PLS); 0000 0000 5396 3610 (Goeckner, MJ); 2008008261‏ (Goeckner, MJ)
    Use the DOI persistent link to see the abstract. A subscription or fee may be necessary to view the article.

Works in Treasures @ UT Dallas are made available exclusively for educational purposes such as research or instruction. Literary rights, including copyright for published works held by the creator(s) or their heirs, or other third parties may apply. All rights are reserved unless otherwise indicated by the copyright owner(s).